I'm planning my next build already. Yep, another Sherman, but this time, the little know M4A6.
A minimal amount were produced (75 -100) but never used in combat and non are known to have survived. They were essentially an M4A4 (Sherman V) with an M4 (Sherman 1) cast front nose. Like the V, the lengthened hull was needed for an even larger engine. My plan is to use a Tasca 1c Composite hull and cut off the front end and graft it onto a Tasca V hull. I have probably just enough info to create a reasonably accurate model but casting the net to see if I can find anything else - especially image wise.
This is what I've been able to find so far...
I have no way of knowing if this is accurate? - http://moderndrawings.jexiste.be/WW2Dra ... n/M4A6.htm
Any other golden nuggets of info will be gratefully received
Gary
Looking for info - M4A6
- Gary Boxall
- Site Admin/Founder
- Posts: 2476
- Joined: 18 Jul 2014, 21:34
- Location: Auckland New Zealand
Looking for info - M4A6
Hi. My name is Gary and I'm an ex-Shermaholic....
- Philipp Gross
- Site Admin/Founder
- Posts: 5122
- Joined: 19 Jul 2014, 23:40
- Location: Frankfurt
- Contact:
Re: Looking for info - M4A6
You're certainly ambitious
I have no definite proof for anything, but since both M4A4 and M4A6 were made by Chrysler it seems reasonable that both would share a lot of features and especially dimensions.
Concerning the hull, it might be easier to add a piece to the rear of the composite hull rather than chopping up the front?
Philipp
I have no definite proof for anything, but since both M4A4 and M4A6 were made by Chrysler it seems reasonable that both would share a lot of features and especially dimensions.
Concerning the hull, it might be easier to add a piece to the rear of the composite hull rather than chopping up the front?
Philipp
Completed Campaigns:
- Gary Boxall
- Site Admin/Founder
- Posts: 2476
- Joined: 18 Jul 2014, 21:34
- Location: Auckland New Zealand
Re: Looking for info - M4A6
Thanks Philipp.
By adding the composite cast front, it'll be easier to hind the styrene join behind a weld seam. Otherwise you'll need to make the join invisible further back. I've just ordered a couple of sprues from Asuka (Tasca) with 1c composite and V hulls so I won't waste an entire kit if it goes wrong.
Gary
By adding the composite cast front, it'll be easier to hind the styrene join behind a weld seam. Otherwise you'll need to make the join invisible further back. I've just ordered a couple of sprues from Asuka (Tasca) with 1c composite and V hulls so I won't waste an entire kit if it goes wrong.
Gary
Hi. My name is Gary and I'm an ex-Shermaholic....
- Rod Dumouchel
- Posts: 290
- Joined: 20 Jul 2014, 07:10
- Location: Edmonton, Alberta Canada
- Contact:
Re: Looking for info - M4A6
Hi Gary,
I think you have everything I have on this beast. It did use the M4A4 hull with the Cast nose, power train was not the Chrysler bank, but a dual Cat diesel I think. I'll take a look tonight and see if I have anything else.
Regards,
Rod
I think you have everything I have on this beast. It did use the M4A4 hull with the Cast nose, power train was not the Chrysler bank, but a dual Cat diesel I think. I'll take a look tonight and see if I have anything else.
Regards,
Rod
- Justin Wooding
- Posts: 1343
- Joined: 21 Jul 2014, 09:34
- Location: Wollongong, NSW, Australia
Re: Looking for info - M4A6
How is this project going Gary? It's looks like an interesting conversion!
Woody...
Trying hard to do some modeling!
Trying hard to do some modeling!
- Gary Boxall
- Site Admin/Founder
- Posts: 2476
- Joined: 18 Jul 2014, 21:34
- Location: Auckland New Zealand
Re: Looking for info - M4A6
Hi. My name is Gary and I'm an ex-Shermaholic....
- Justin Wooding
- Posts: 1343
- Joined: 21 Jul 2014, 09:34
- Location: Wollongong, NSW, Australia
Re: Looking for info - M4A6
thanks!
I am just working my from bottom to top in the forum index trying to catch up on all the good stuff
I am just working my from bottom to top in the forum index trying to catch up on all the good stuff
Woody...
Trying hard to do some modeling!
Trying hard to do some modeling!